Mechanical watches naturally gain or lose some time, but a simple accuracy log can show whether the change is normal for your movement or a sign that it needs attention. This guide explains how to synchronize a watch, record its daily rate, compare positions, interpret beat error and amplitude, check for magnetism or low power reserve, and decide when to seek regulation or service.
Overview
Checking mechanical watch accuracy is less about finding one perfect reading and more about identifying a consistent pattern. A watch may perform differently when fully wound, nearly run down, worn on the wrist, or left resting crown-up overnight. Position also matters because gravity affects the balance and escapement in different orientations.
For a useful baseline, measure the watch over several consecutive days rather than judging it from a single morning. Compare it with a dependable reference such as a synchronized phone, radio-controlled clock, or another trusted time source. Record the conditions each time so that a later change has context.
If you own an automatic watch, keep in mind that wrist activity affects how much energy reaches the movement. Before starting a test, read the manufacturer’s instructions for winding and setting. The automatic watch buying guide explains how power reserve and everyday wearing patterns influence ownership.
What to track
Daily rate
Daily rate is the amount of time a watch gains or loses during a defined period. To calculate it, compare the watch with your reference at the start and end of the interval. If it is two seconds ahead after 24 hours, record +2 seconds per day. If it is three seconds behind, record -3 seconds per day.
Use the same reference and checking method throughout the test. Avoid rounding a reading that is only approximate; write down the observed result and note whether the watch was worn, resting, or recently wound.
Power reserve and winding state
Record whether the watch was fully wound, partially wound, or close to stopping. A mechanical movement may show a different rate as its mainspring loses energy. If the watch stops earlier than the stated or expected power reserve, document the elapsed time and the winding method before contacting a watchmaker.
Position
For a practical home test, note the position in which the watch spends the night: dial up, dial down, crown up, or crown down. You do not need to test every position to learn something useful. Repeating the same overnight position makes your log more consistent; comparing several positions can reveal positional variation.
Beat error, amplitude, and timegrapher readings
A timegrapher can display several movement characteristics:
| Reading | What it describes | How to use it |
|---|---|---|
| Rate | Estimated gain or loss over a day | Compare with your real-world daily log, not as a standalone verdict. |
| Beat error | The difference between the two impulse directions of the balance | A persistent abnormal reading can justify professional inspection or regulation. |
| Amplitude | The swing of the balance | Compare readings at a similar winding state and lift angle; do not treat one number as universal. |
| Lift angle | A setting used by the device to calculate amplitude | Use the movement maker’s specification when available; an incorrect setting makes amplitude less meaningful. |
Timegrapher results are diagnostic measurements under controlled conditions. They do not exactly reproduce the way a watch behaves through a full day on the wrist. If you use a device, record the movement reference, winding state, position, and settings alongside the readings.
Manufacturer tolerance and movement specifications
Compare your results with the tolerance published for your exact watch or movement, if one is provided. Tolerances vary by caliber, certification, age, service condition, and brand testing method, so a generic accuracy range should not replace the owner’s manual or warranty documentation. Record the source and revision date of any specification you use.
Magnetism and physical symptoms
A sudden, unusually large change in rate—especially a watch that begins gaining significantly—can be consistent with magnetization, although it is not proof. Possible exposure sources include strong magnets in speakers, magnetic closures, tablet covers, bags, tools, and some electronic accessories. Other explanations include shock, moisture, low power, or a movement that needs service.
Do not place a valuable watch on a household magnet to test it. A watchmaker or qualified service center can use an appropriate demagnetizer and then verify the result. For broader ownership guidance, see the luxury watch maintenance schedule.
A simple accuracy log
Copy this table into a notes app or print it. The goal is consistency, not laboratory precision.
| Date and time | Reference difference | Watch state | Position or wear | Notes |
|---|---|---|---|---|
| Full / partial / low | ||||
| Full / partial / low | ||||
| Full / partial / low | ||||
| Full / partial / low | ||||
| Full / partial / low |
Cadence and checkpoints
Establish a baseline after purchase or service
After buying a watch, regulation, or service, allow your normal wearing pattern to settle before drawing conclusions. Synchronize it to a reliable reference, wind it according to the manufacturer’s instructions, and record readings for at least several days. A longer observation period produces a more useful average than a single check.
Keep the watch in ordinary conditions during the baseline. Note travel, unusually high activity, a long period in a drawer, a strong impact, or a change in how frequently you wind it. If you are evaluating a pre-owned watch, preserve the original log and any service records with the rest of the ownership documentation. The pre-owned luxury watch checklist covers related records and inspection points.
Monthly or quarterly checks
For a watch that appears stable, a brief monthly or quarterly check is usually more useful than daily monitoring forever. Compare its current rate with the baseline, inspect the crown and crystal visually, and confirm that the power reserve still behaves as expected. More frequent checks make sense after travel, a drop, water exposure, suspected magnetism, or a noticeable change in performance.
When crossing time zones, synchronize carefully rather than using a change in local time as evidence of poor accuracy. The guide to setting a world time or GMT watch explains how time zones, date lines, and daylight saving changes can create apparent discrepancies.
Use a repeatable test sequence
- Choose a reliable reference and record the exact synchronization time.
- Wind or wear the watch consistently, following the movement’s instructions.
- Check it at the same time each day and calculate the gain or loss.
- Record the watch’s position and whether it was worn overnight.
- Continue for several days, then compare the average with the applicable manufacturer tolerance.
- If using a timegrapher, repeat readings in multiple positions and at a comparable winding state.
How to interpret changes
A small, consistent daily difference may simply reflect the movement’s normal regulation. A steady gain or loss across several days is more informative than alternating readings caused by changing positions or inconsistent measurement times.
- Gradual drift: Compare the average with the watch’s documented tolerance. A service professional can determine whether regulation is appropriate.
- Sudden large gain: Consider magnetism, shock, or an escapement issue. Stop experimenting with magnets and arrange an inspection if the change persists.
- Erratic readings: Check your reference, synchronization method, winding state, and measurement timing before assuming a mechanical fault.
- Short power reserve: Confirm that the watch was wound correctly and repeat the test. Persistent short reserve, stopping, or slipping may require service.
- Position-dependent variation: Some variation is expected, but a marked or worsening difference across positions is useful information for a watchmaker.
- After impact or moisture exposure: Do not wait for the accuracy log to prove a problem. Have the watch inspected, particularly if condensation appears under the crystal or winding feels abnormal.
Accuracy is only one part of mechanical watch health. A watch can keep acceptable time while still needing attention for degraded seals, dried lubricants, worn components, or damage. Avoid opening the case or adjusting the regulator yourself unless you have the tools and training to do so.
When to revisit
Return to your accuracy log on a monthly or quarterly schedule, and restart a multi-day baseline whenever the watch is serviced, regulated, magnetized, dropped, exposed to moisture, or stored for an extended period. Revisit it after a major change in wearing habits as well: switching from daily wear to occasional use can change the winding pattern and make old comparisons less useful.
Before contacting a watchmaker, gather the watch reference, movement reference if known, purchase or service date, warranty documents, your daily-rate table, power-reserve observations, and any timegrapher readings. Describe what changed and when. This gives the professional a clearer starting point than saying only that the watch is “running fast” or “running slow.”
Take these practical next steps:
- Synchronize the watch with a dependable reference.
- Record its condition, winding state, and wearing pattern.
- Log the rate for several consecutive days.
- Repeat the test after changing the overnight position.
- Compare the pattern with the exact manufacturer specification, if available.
- Seek qualified inspection for sudden changes, suspected magnetism, impact, moisture, stopping, or persistent readings outside the documented tolerance.
A short, consistent log turns a vague concern into useful ownership information. Keep it with your watch records and update it whenever the watch’s circumstances change.